Last week, residents complained about the water quality at a Village Board meeting and brought pictures of children with orange hair, damaged pipes and water sample results that documented the iron content was some three times the normal level.

This week, after action taken by the village, residents say things are looking up.

“It is looking better, this is good news,” Karol Armbruster, one of the residents affected by the rusty water, said Tuesday.

Her daughter has had to visit a hair salon on two occasions due to the rust in the water, she said. “It was turning orange and a had a little green tint,” she said,

“It doesn’t seem to be as bad,” said Debbie Way, another resident.

The water problems began Nov. 19 when the motor that runs Well 14 broke. At that time, village officials began sending water to the area from other wells.

The rust is the result of a change in direction of the water flow in the pipes.

“The cause of the rust was a build-up of iron deposits inside the pipes for some 50 years,” said Michael Pubentz, Montgomery public works director. ( source )

For these folks water conditions will improve once the new well pump comes online, according to the article, but what about YOUR water? Do you know how much iron or other metals it contains? While some metals (like iron) usually pose more of an aesthetic problem, other metals such as lead, mercury, chromium, etc. can have lasting detrimental health effects.

Moral of the story?

If you notice sudden changes in water quality could mean problems with the safety of your water and only testing the water for its purity will let you know for sure if the changes mean action needs to get taken by your water company or, if your water comes have a private well, you need to take action.

In this case the water district had a pump fail and needed to redirect water through different lines that had not seen a lot of use in a long time and years of corrosion got pumped to people’s homes. We believe that local residents’ seeking testing and banding together to lobby for prompt action on the part of the water company resulted in the situation getting cleared up a lot faster than may have happened if residents had not presented test results along with their complaints.

Certified water testing data gets results. So, as we like to say, “It’s your water, your health… and ultimately your LIFE.”

Take an interest in the quality of your water and perform spot checks from time to time — especially if you notice a ‘change’ in the color, taste or smell of your water. Doing so could, in some cases, possibly save your life or the life of a loved one.

Interested in removing iron from drinking water? Whether you need a replacement 10″ iron filter cartridge, replacement 20″ iron filter cartridge or a whole house iron removal system, we believe FilterWater.Com may have the perfect solution for your water quality situation.

Whole House Greensand Water Filter Reduces Iron, Manganese and Hydrogen Sulfide

Commercial Iron Removal Water Filter Reduces Iron, Manganese and Hydrogen Sulfide

]]> http://test-for.com/blog/2012/01/orange-hair-from-tap-water-too-much-iron-in-the-water/feed/ 0 http://test-for.com/blog/2012/01/nsf-certified-water-filter-homepure-ap-0930-a-%e2%80%98good-product%e2%80%99/ http://test-for.com/blog/2012/01/nsf-certified-water-filter-homepure-ap-0930-a-%e2%80%98good-product%e2%80%99/#comments Tue, 10 Jan 2012 21:56:44 +0000 Water Testing Blog http://watertestingblog.com/?p=5110 A plethora of water quality improvement products exists and sometimes the choices seem overwhelming — even to folks with more than a little knowledge on the topics of water quality and water quality improvement.

Today’s inquiry came to us from ‘Ric C’ who asked a very wise question about a water filtration unit he may wish to purchase (HomePure AP-0930):

Hi
Am dealing with a product that has an NSF certification, and below is the address;

http://www.nsf.com/Certified/DWTU/Listings.asp?TradeName=homepure&Standard=&ProductType=&PlantState=&PlantCountry=&PlantRegion=&submit3=SEARCH&hdModlStd=ModlStd

Does this mean the product is good?

Quite honestly, we have never seen the HomePure AP-0930 before but as we said previously, the marketplace has a ton of water filtration units out there and we seriously doubt that anyone could know the in’s and out’s of every single water filtration unit currently available for purchase.

With that said, we looked at the NSF credentials supplied by Ric and saw that this unit has tested and certified to NSF/ANSI STANDARD 042 (Drinking Water Treatment Units – Aesthetic Effects) for the reduction of chlorine taste and odor as well as NSF/ANSI STANDARD 053 (Drinking Water Treatment Units – Health Effects) for the reduction of volatile organic compounds (VOC’s).

While having NSF Certification does give the HomePure AP-0930 a bit of credibility, please keep in mind that not every water filter will work in every application — even with NSF, WQA, etc. certifications to back up its capabilities.

Think of it this way: A high quality hammer won’t do you a bit of good when you need to turn a screw.

Testing your water first?

Yes! Do it! Test your drinking water before spending money on a water filter!

Before investing in a water filter for your home or office make sure you test your water for as wide a range of potential contaminants as possible. Doing so could save you the expense and aggravation associated with installing a filter that addresses the wrong water quality issues.

Anything specific about the HomePure AP-0930 catch your eye?

We like the fact that the HomePure AP-0930 has NSF certifications. As we said before, it means the unit certainly has some credibility.

One thing we did not like about the unit dealt w/ it inability to filter out heavy metals such as lead, copper, iron, chromium, etc. In our opinion a well-rounded, general purpose water filter would also have the ability to remove/reduce levels of heavy metals in drinking water.

Older homes most likely contain metal piping and the majority of public water systems contain metal pipes, as well. “But, we live a newly constructed home.” Does not matter (in our opinion). Newer homes, while mostly containing PVC or some other type of plastic piping, still get connected to public water systems that contain miles and miles of metal pipes.

Depending upon the quality of the water when it leaves the water treatment plant, it has the opportunity to pick up anywhere from traces of metals to noticeable levels of metals as it travels through those miles of metal pipes to homes and offices on the water system.

Interesting fact: The literature for the HomePure AP-0930 water filter system did mention metals and say that metals in water may cause problems, but the HomePure AP-0930 does not remove/reduce metals.

Replacement filters for the HomePure AP-0930?

According to the NSF web site, the HomePure AP-0930 uses a replacement filter element with model number “AP-0931″. A quick search of three popular online water filter web sites (FilterWater.Com, FiltersFast.Com and WaterFilters.Net) and a google search yielded no locations where a person could purchase replacement filters.

Not a particularly good sign! What happens in 3 months or a year when the original filter kicks the bucket?

Moral of the story?

Not all water filter systems are created equal and even though some bear seals of certification and/or endorsement from well-known, reputable organizations such as NSF or WQA, not every one of those ‘certified’ products will clean up every possible water quality condition.

So, test your water to see what problems/issues it may have and THEN set about the task of locating the correct water quality improvement device for your water.

Look for products that bear the NSF and/or WQA logos, but do not assume the logo automatically means that a particular device will do what you need it to do.

Oh, and one last thing: Check to make sure you can easily acquire replacement filters for any water filter you consider buying.

Natural Contamination

Contamination of natural bodies of water (including lakes, streams, aquifers and groundwater) can have numerous characteristics and sources. While many believe only ‘big business’ causes water pollution, all humans and animals release waste products that eventually find their way into lakes, rivers, streams, oceans, etc.

Scientists refer to this occurrence as ‘nutrient loading’ and when it happens too often in one location nutrient loading may result in bacterial contamination that eventually becomes detrimental to the environment and harmful to humans who unknowingly consume the water.

Contaminants often included in the list of ‘natural’ contaminants include things such as coliform bacteria, nitrates, nitrites, etc.

Therefore, if your drinking water comes from the ground (i.e. a well) you may have ‘natural’ things to worry about… and even municipal (i.e city, town, etc.) water sources have problems from time to time. Need proof? Ever hear of things called boil water advisories?

Unnatural Contamination

This type of contamination typically comes from accidental or intentional dumping of foreign matter into or too close to a body of water either on the the surface or under the ground.

Common sources of groundwater and surface water contamination include improper disposal of industrial waste products, faulty septic tanks and waste water storage or processing equipment, landfills, pesticides and fertilizers.

Many experts believe the practice of hydraulic fracturing certainly belongs in the category of unnatural water contamination and pollution… and, of course, many other experts (who often work for or get funding from gas drilling companies) believe hydraulic fracturing poses no (or extremely limited) risks to the environment.

Thus far OUR opinion falls more in line with the folks who suspect that fracking (the nickname for hydraulic fracturing) may pose risks and that more research needs to get done before we turn the Marcellus Shale Formation under the United States into swiss cheese whose holes we filled with ‘questionable’ fluids containing a host of unknown compounds.

Moral of the Story?

You will NEVER know if your water contains unwanted contaminants UNTIL YOU GET IT TESTED and for that task you have several options: 1) Test for the basics yourself using a drinking water test kit; 2) Have a qualified drinking water laboratory test your water; or 3) test for the basics yourself with a water quality test kit and enlist the services of a qualified water testing lab from the list posted on the EPA’s Safe Water Web Site

In tests of 44 properties in Jasper County, 19 showed high levels of lead, prompting the city’s mayor to ask the U.S. Environmental Protection Agency and the Missouri Department of Natural Resources for help in testing for, and cleaning up, the element, according to the Los Angeles Times.

For more than 100 years, beginning in the mid-19th century, Jasper County was at the worldwide forefront of lead and zinc mining. The area included town names like Leadville Hollow and Minersville.

According to Dan Pekarek, director of the Joplin Health Department, a waste product from lead mining called “chat” was dumped in several spots around the city of Joplin, and simply covered with soil. Those sites we likely exposed when the F-5 tornado ripped through the city. ( source )

So… What does that mean for the residents of Joplin in terms of water quality and drinking water safety? It means they will more than likely begin regular testing for lead and other potentially dangerous metals in their drinking water!

The United States Environmental Protection Agency has determined that consuming food and drink containing levels of lead at or above 15ppb (parts per billion) can cause serious health problems.

Why did companies dump ‘chat’ all over the place?

At the time no one probably knew the dangers posed by the material so government did not really care where the material ended up. Hence the reason the article mentioned how people used it as fill material under houses, in yards, etc.

Now, however, science and the medical profession both agree that material containing such high levels of lead pose quite a threat, mining companies would need piles and piles of permits before they could dispose of a substance like ‘chat’ and they would more than likely remain on the hook for the safety of surrounding areas for many years.

Testing for lead in water? Soil?

Can the average person test for the presence of lead in their water and soil? Absolutely! SenSafe makes several affordable products that work well for field testing.

Right now (11/09/11) TestProducts.Com has SenSafe’s Lead in Water Test Kit available at a discounted rate of around 18 dollars for two tests and you can use the kit to test for the presence of lead in either soil or water.

A company called WaterSafe also manufactures a Lead in Water Test Kit, but that kit does not include instructions for determining lead levels in soil.

Below you will find excerpts from an article published last week about high levels of lead found in public fountains and sinks:

Even as universities across the country are banning bottled water, alarms are going off about the safety of the water coming out of drinking fountains at some Canadian campuses.

Concerns over water quality at school drinking fountains are not new. A US investigation in 2009 turned up lead-contaminated drinking water at schools in every American state. Some of the lead came from the school’s own well or local water supplies, while lead-soldered pipes were identified as culprits in other cases. In Canada, one study found that 27 per cent of “first draw” samples taken in Ontario schools had high levels of lead, and 9 per cent still had high levels even after the system was flushed. source

We included that last paragraph so that no one would say, “Oh, well see? It’s just a Canadian problem. We’re safe here in the United States…” And yes, we get emails from people all the time saying silly stuff like that.

Why has lead in drinking fountains gone unnoticed for so long?

Honestly, we do no know. We’d guess that many people just assumed removal of older, lead-baring piping inside and hooked up to drinking water fountains would take place when all of the other piping in buildings got replaced, and as you can see they must have guessed incorrectly.

“Recently, the Albany City School District voluntarily decided to test the water in all of their school buildings. In at least six school buildings, 32 faucets came back with high, unsafe levels of lead in the water. While one would think this problem would only affect older buildings, some of the affected faucets were in buildings that had been renovated.” source

How do we test for lead in drinking fountains?

While qualified laboratories use sophisticated testing equipment that may cost thousands of dollars, the average person (like you and me) can acquire simple, easy-to-use and highly affordable lead in water test kits.

One kit in particular, the Watersafe Drinking Fountain Detective Kit (WS-207T), includes supplies for testing (12) twelve water samples, comes with a data tracking sheet to record results, provides results in just ten minutes, requires no special training or testing skills, and contains an interactive CD designed to help create a presentation template for the testing data.

What about other metals? Can we test for those, as well?

Absolutely! While more complicated test kits do exist, the average person (like you and me) can use simple, dip-n-read test strips for metals in water such as the SenSafe Water Metals Test Kit to perform on-the-spot testing. Products like this detect heavy metals such as lead, copper, iron, chromium, nickel, cadmium, etc. and alert users to the presence of metals — down to levels as low as 10 parts per billion!

Note: Although Sensafe Water Metals Check does have the ability to detect really low amounts of metals in water, it does not have the ability to tell user which metal or metals it has detected.

As an example, ‘J. Mampilly’ from India installed a system and now seeks to determine if he has installed the correct unit. He asked,

I would like to know about how i can confirm the effectiveness of my water purifier. Labs in India that can certify and throw light on the camparative quality of water before and after using a water purifier. Thank You

Unfortunately we do not have familiarity with water testing laboratories in India and cannot directly assist with this situation. We can suggest, however, that you contact your local health department and ask them for a list of certified water testing laboratories in your area.

Coliform Bacteria Test Kit

Before…

In order to know what type of filter or what filtering capabilities you should purchase, invest (yes, we said invest) in a thorough water analysis performed by a qualified water testing laboratory. Here, again, we suggest contacting your local board of health and asking them, for a list of certified drinking water testing labs. Alternatively, or if no labs exist in your immediate vicinity, you can use the services of accredited water testing companies such as National Testing Labs.

No matter what, though, always have your water tested BEFORE deciding on a water treatment system. Oh, and one more thing: Don’t think for one second that a salesperson doing an in-home water test has the same water testing tools or qualifications as a reputable water testing laboratory. Remember: 99% of all salespeople attempt to sell things and not accurately analyze a situation — especially if accurately diagnosing a situation could cost them a sale!

And after!

As ‘J. Mampilly’ has done, we should ALL take an interest in comparing the quality of water that comes out of our water filter systems. Only then will we know if the money we invested in (not spent on!) a quality drinking water filter system performs as expected.

Testing water quality beforehand gives us not only an idea of what we need to filter out of our water, but also a checklist of water quality parameters to monitor post-filtration. Should follow up water testing reveal that these ‘issues’ did not get corrected or suddenly show up months after the installation of a water system, perhaps the water filter has stopped working or never really worked properly in the first place and needs service of some sort.

And in conclusion…

Many people go through life ‘deaf, dumb and blind’ when it comes to the quality of their water — until an (initially) unexplainable health problem pops into their life. Then, and unfortunately sometimes too late, those same people get very interested in the quality of their water and want to punish or otherwise penalize others for allowing them to consume tainted, polluted and/or contaminated drinking water.

Although we feel much sympathy for the victims of poor quality drinking water, most of us here in the United States have the ability to at least once every great while perform basic testing for critical water quality parameters such as heavy metals (i.e. lead, mercury, copper, iron, etc.), coliform bacteria, pesticides (i.e. atrazine and simazine), chlorine levels (free and/or total), total hardness, total dissolved solids, and many others.

Many times the contaminants in a water supply will have no taste, carry no odor and not appear before the naked eye. Only testing will alert you to their presence.

Oh, how we wish the possibility of cyanide, the same deadly compound used to execute prisoners in gas chambers, entering drinking water supplies did not exist.

Despite cyanide’s reputation as a known killer, many industries still find it quite useful in a number of manufacturing processes. As an example, metal plating facilities would need to charge much more for their finished goods if they could not use cyanide in their operations.

In theory, as long as every company using cyanide keeps accurate track of every single drop and no one breaks any laws regulating the use, storage and disposal of cyanide we ought to have nothing to worry about, right? RIGHT?

Sorry, but those of us who live in the real world know darn well that a good number ‘fat cat’ business types don’t give a rat’s stinky butt about what happens to the water in YOUR area if cutting corners here and there when it comes to environmental safety practices will help the bottom line.

Testing for cyanide? Easy to do?

As our friends over at Water Testing Blog always say, “Nothing takes the place of testing performed by a qualified, certified water testing lab…” but it never hurts to do a little testing on your own between lab tests just to keep an eye on things.

The test kits below will give you, the average person, the ability to test for dissolved cyanide in water:

Cyanide in Water Test Kit

Meter to Test for Cyanide

]]> http://test-for.com/blog/2011/06/test-for-cyanide-in-drinking-water/feed/ 0 http://test-for.com/blog/2011/06/test-for-metals-in-drinking-water/ http://test-for.com/blog/2011/06/test-for-metals-in-drinking-water/#comments Fri, 17 Jun 2011 13:03:55 +0000 Test For Admin http://test-for.com/blog/?p=958 Last week we touched on the topic of testing for potentially toxic heavy metals in human hair — a very wise thing to do if you have reason to believe your tap water or other aspect of your everyday environment may contain excess amounts of heavy metals.

Now the question becomes, can a person test their water for heavy metals? Absolutely, and at least three options exist: 1) At-Home Drinking Water Test Kits; 2) Mail-In Laboratory Testing; 3) Lab Testing by a Local, Certified Water Testing Laboratory.

For option ’3′, check your local phone book or browse through the listings of labs certified to test drinking water on your state via the USEPA’s Safe Water Web Site.

For option ’2′ we suggest taking a look at the mail-in water test kits offered by National Testing Laboratories or considering a kit such as the Premium Drinking Water Testing Kit which tests specifically for metals (plus fluoride & pH).

For option ’1′ we suggest purchasing a bottle of the Heavy Metals Check test strips from SenSafe. Although this product will not identify heavy metals in your drinking water, it will tell you the overall concentration in ppb (parts per billion) of heavy metals in your drinking water. Each bottle comes with 50 tests so you can either perform testing on multiple water sources OR perform periodic testing on just one water source.

If you want a broken down list of heavy metals contaminating your water, consider Option ’2′ again and think about using the Premium Drinking Water Testing Kit.

Water Metals Check

Coliform Bacteria Test Kit

]]> http://test-for.com/blog/2011/06/test-for-metals-in-drinking-water/feed/ 0 http://test-for.com/blog/2011/06/test-for-metals-in-the-body/ http://test-for.com/blog/2011/06/test-for-metals-in-the-body/#comments Fri, 10 Jun 2011 13:03:05 +0000 Test For Admin http://test-for.com/blog/?p=952 With all the talk about excess metal contamination in our environment (in the air, in the water, in the soil, in the ground & even in the foods we eat!) it comes as no surprise that people have started to wonder if they, too, have become an unwilling recipient of too many metals.

That’s where a test like the Toxic Element Exposure Hair Testing Kit comes in handy. It gives people the ability to test their own body’s (or a loved one’s body) for recent exposure to 31 harmful and potentially harmful heavy metals — all with just a simple snip of hair from the head.

So if you suspect exposure to metals through drinking water contamination, airborne contaminants or any other means, you should definitely consider having yourself tested for Arsenic, Lead, Mercury, Cadmium, Chromium, Beryllium, Cobalt, Nickel, Zinc, Copper, Thorium, Thallium, Barium, Cesium, Manganese, Selenium, Bismuth, Vanadium, Silver, Antimony, Palladium, Aluminum, Platinum, Tungsten, Tin, Uranium, old, Tellurium, Germanium, Titanium, and Gadolinium.

The Toxic Element Exposure Hair Testing Kit provides results in just 7 to 10 days and best of all REQUIRES NO INVASIVE PROCEDURES (like needles).

A chromium in water test strip manufactured by WaterWorks, a sister product line of SenSafe, detects Chromium (VI) levels as low as 0.1 ppm (mg/L) and as high as 50 mg/L (ppm) in under 2 minutes.

National Safety Products carries this product, which comes with 50 tests per bottle, at a cost of less than 40 cents per test.

Chromium Test Strips